Akuvox A02 Access Control Terminal Administrator Guide

Thank you for choosing the Akuvox A02 access control terminal. This manual is intended for the administrators who need to properly configure the access control terminal. This manual is written based on firmware version: 101.30.10.18, and it prov...

Akuvox Access control terminals A02 incorporate a door controller and an RIFD reader in one standalone device, thus saving your solution costs. It is equipped with a card reader (125kHz and 13.5MHz) which is currently capable of handling a majority ...

Add High Security Mode .

Status : this section gives you basic information such as product information, network information, and log related configurations such as access log and so on. Network : this section covers LAN port setting. Access Control : this section c...

Before configuring Akuvox A02, please make sure the device is installed correctly and connects to a normal network. Using the Akuvox IP scanner tool to search the device IP address in the same LAN. Then use the IP address to log in to the web browse...

Time settings on the web interface allows you to set up the NTP server address that you obtained to automatically synchronize your time and date. When a time zone is selected, the device will automatically notify the NTP server of the time zone so t...

Brightness Setting If you want to brighten up the brightness in order to see the card reader at greater ease in an environment with higher light intensity, you need to set up the related parameters on the web Device >Light > Light of Swiping Car...

Volume and tone configuration include microphone volume, the AD volume, keypad volume, speaker volume, tamper alarm volume, and open-door tone configuration. Moreover, you can upload the tone you like to enrich your personalized user experience. V...

You can configure the default DHCP mode ( Dynamic Host Configuration Protocol ) and static IP connection. Moreover, you can set up an IP address, Subnet Mask, Default Gateway, and DNS servers. To configure it on web Network > Basic > LAN Port i...

You can configure the relay switch(es) for door access on the web interface. Relay Switch Setting To configure it on web Access Control > Relay > Relay interface. Parameter Set-up : Trigger Delay (Sec) : set the relay trigger delay...

Configure Door Access Schedule Door access schedules can be applied to the door access control intended for individual users or a group of users created. Manage Relay Schedule Set the corresponding relay always open at a specific time. This fe...

A02 access control terminal allows users to open door by PIN code, RF card, NFC, HTTP command, and exit button. Moreover, you can import or export the configured files including access control information. Configure RF Card for Door Unlock To co...

Tamper Alarm Setting The tamper alarm function serves as a protection against any unauthorized removal of the devices by triggering off the tamper alarm on the device. To configure it on web System > Security > Tamper Alarm interface. P...

Access Log You can search and check door logs on the device web Status > Access Log interface. Parameter Set-up : Remote Door Log Enabled Remote Server : remote server IP address. Authorization Mode : there are four options:...

System Log for Debugging You can export the system log to a local PC or a remote server for debugging. To set up the function on the web System > Maintenance > System Log interface. Parameter Set-up : Log Level : log levels range f...

Akuvox devices can be upgraded on the device web interface. Go to System > Upgrade interface. Note Firmware files should be in .rom format for upgrade.

You can import or export encrypted configuration files to your Local PC for backup. Go to System > Maintenance > Others interface.

Configurations and upgrading on the device can be done on the web interface via one-time auto-provisioning and scheduled auto-provisioning via configuration files, thus saving you from setting up configurations needed one by one manually on the acce...

Integration via Wiegand A02 access control terminal can be integrated with the third-party devices via Wiegand. To configure it on the web Device > Wiegand interface. Parameter Set-up : Wiegand Display Mode : Wigand Card code formats...

Modify the Password To modify web interface password, you can do it on device web System > Security > Web Password Modify interface. Select Admin for the administrator account and User for the user account. Click the Change Password tab to...

Reboot Reboot the device on the web System > Upgrade interface. To set up the device restart schedule on web System > Auto Provisioning > Reboot Schedule interface. Reset To reset the device, go to System > Upgrade interface. ...