Akuvox S562 Series Indoor Monitor Administrator Guide

Thank you for choosing the Akuvox S562 series indoor monitor. This manual is intended for the administrators who need to properly configure the indoor monitor. This manual is written based on firmware 562.30.10.115, and it provides all the confi...

It can be connected to the Akuvox door phone for audio/video communication, unlocking, and monitoring. Residents can communicate with visitors via audio/video calls, and it supports unlocking the door remotely. It is more convenient and safer for re...

Status : This section gives you basic information such as product information, Network Information, account information, etc. Account : This section concerns the SIP account, SIP server, proxy server, transport protocol type, audio & video codec...

Akuvox indoor monitor system settings can be either accessed on the device directly or on the device web interface. Device Start-up Selection When you first start up the S562 series indoor monitor, you need to perform start-up initialization, wh...

Language Setting Set up the language during initial device setup or later through the device or web interface according to your preference. Language Setting on the Device To select the desired language, go to Settings > Time & Language ...

Akuvox indoor monitor provides you with various types of ringtones and volume configurations. You can configure them on the device directly or on the web interface. Volume Configuration Configure Volume on the Device You can adjust th...

Screen Display Setting on the Device You can configure a variety of features of the screen display in terms of brightness, screen saver and font size, etc. You can do this configuration on the device Settings > Display screen. Pa...

Device Network Configuration To ensure normal functioning, make sure that the device has its IP address set correctly or obtained automatically from the DHCP server. Configure Network Connection on the Device To check and configure the n...

Contacts Configuration on the Device You can add, edit, and delete contacts on the device Contacts> Local Contacts screen directly. Add Contacts Go to Contacts > Local Contacts screen and press the Add icon to add a contact. Ed...

IP Call & IP Call Configuration An IP call is a direct call between two intercom devices using their IP addresses, without a server or a PBX. IP calls work when the devices are on the same network. Make IP Calls To make a direct IP call ...

Call Auto-answer Configuration You can define how quickly the device should respond by answering the incoming SIP/IP call automatically by setting up the time-related parameters. To enable or disable the function on the web Account > Advanced ...

You can read, create, and delete messages on the Message screen. Manage Notification Messages displayed in Notification are from property managers. This feature is only available when using SDMC or Akuvox SmartPlus. To configure it, navigate...

Audio Codec Configuration The door phone supports four types of Codec (PCMU, PCMA, G729, and G722) for encoding and decoding the audio data during the call session. Each type of Codec varies in terms of sound quality. You can select the specifi...

Relay Switch Setting Local Relay Setting A local relay is an external unit that is physically nearby and directly connected to the intercom device. It allows the intercom system to trigger actions, such as unlocking a door, based on user inpu...

Monitor and Image Monitor Setting You can add up to four video streams using RTSP. If the Display in Call function is enabled, the video of the added monitor device will show up when it calls the indoor monitor. Navigate to Device > Mon...

You can summon a lift via the lift control feature. Configure Lift Control To enable and set the display status Lift icon on the device web Device > Lift > Lift Control interface. Parameter Set-up : Status : enable or disable the l...

Provisioning Principle Auto-provisioning is a feature used to configure or upgrade devices in batch via third-party servers. DHCP, PNP, TFTP, FTP, and HTTPS are the protocols used by the Akuvox devices to access the URL of the address of the ...

If you want to check on the calls inclusive of the dial-out calls, received calls, and missed calls in a certain period of time, you can check and search the call log on the device web interface and export the call log from the device if needed. ...

Akuvox devices can be upgraded on the device web interface. Navigate to Upgrade > Basic interface. Note Firmware files should be .rom format for an upgrade.

You can import or export encrypted configuration files to your Local PC. Navigate to Upgrade > Advanced > Others interface if needed.

System Log for Debugging System logs can be used for debugging purposes. You can set up the function on the web Upgrade > Diagnosis > System Log interface. Parameter Set-up : Log Level : log level ranges from 1 to 7 levels. Y...

Smart Living Setting You can control the home sensor through an HTTP command. To configure it on the web Device > Smart Living interface. Parameter Set-up: Status : enable or disable this button. If disabled, the button won't appe...

Modify Device Basic Setting Password To do the configuration on device Settings > Advance Settings > Protected Code screen to choose System Code to change a new password. The default password is 123456. Modify Device Advance Setting Pass...

Reboot Reboot on the Device If you want to reboot the system setting of the device, you can operate it directly on the device setting screen or on the device web interface. To restart the system on device Settings > Advance Settings > R...