--- title: "Integrate Akuvox Devices with the ACR-CRP12 UHF Reader" slug: "akuvox-vehicle-access-control-configuration" status: "update" updated: 2026-11-13T03:02:06Z published: 2026-11-13T03:02:06Z canonical: "knowledge.akuvox.com/akuvox-vehicle-access-control-configuration" --- > ## Documentation Index > Fetch the complete documentation index at: https://knowledge.akuvox.com/llms.txt > Use this file to discover all available pages before exploring further. # Integrate Akuvox Devices with the ACR-CRP12 UHF Reader Integrate the Akuvox ACR-CRP12 UHF reader with an Akuvox door phone or access control terminal to enable vehicle access using windshield-mounted UHF tags. When a registered tag is presented within the reader's detection range, the reader sends the tag data to the Akuvox device for verification. If the tag is authorized, the configured relay triggers the gate. This guide explains the hardware connection and configuration process for both local and SmartPlus Cloud deployments. ## Overview The integration involves the following products: - **Akuvox door phone or access control terminal:** Receives UHF tag data, verifies the credential, and triggers the configured relay when access is authorized. - [**Akuvox ACR-CRP12 UHF Reader**](/v1/docs/akuvox-acr-crp12-tool-administrator-guide)**:** Reads windshield-mounted UHF tags and transmits the tag data to the Akuvox device through Wiegand. - [**Akuvox ACR-CID12 Desktop Card Reader**](/v1/docs/akuvox-acr-cid12-tool-administrator-guide)**:** Reads card numbers, including UHF tag codes, and enters the read data into the card number field when the cursor is placed in that field. - **Akuvox UHF-TAG11 Windshield Tag:** Provides the credential used to identify an authorized vehicle. > [!NOTE] > Note > > - Akuvox door phones and access control terminals with Wiegand feature all support connection with ACR-CRP12. > - Confirm the specific product specifications and installation requirements with Akuvox before deployment. ## System Topology The following example uses the R29S door phone. 1. Connect the ACR-CRP12 to the R29S through Wiegand. 2. Connect the R29S relay to the gate controller or the applicable gate-opening circuit. 3. Place the UHF-TAG11 on the vehicle windshield. 4. When the tag enters the reader's detection range, the ACR-CRP12 reads the tag and sends its data to the R29S. 5. The R29S checks the received credential against the configured access permissions. If access is authorized, the configured relay is triggered to open the gate. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/Vehicle Access Control Topology.png) ## Before You Start Make sure that: - The ACR-CRP12, UHF-TAG11, and other required devices are available. - The required configuration tools and permissions are available for the devices you need to configure. - You have identified the relay connected to the gate-opening circuit. - You know whether the project uses local or SmartPlus Cloud credential management. **Deployment Options** | Deployment | Where to manage credentials | Documentation path | | --- | --- | --- | | Local Deployment | Configure the user and UHF tag credentials on the local device, as described below. | Follow the local configuration steps in this guide. | | SmartPlus Cloud Deployment | Manage resident credentials through SmartPlus Cloud, subject to the project's supported models, firmware, and role permissions. | Follow the cloud configuration links in the SmartPlus Cloud section. | ## Part 1: Configure the ACR-CRP12 Use the ACR-CRP12 configuration tool to connect to the reader and set its Wiegand format. - For detailed reader features, refer to the [ACR-CRP12 Tool Administrator Guide](/v1/docs/akuvox-acr-crp12-tool-administrator-guide). - Click [here](/v1/docs/acr-crp12-tool-1) to download the configuration software. ### Part 1-1: Connect to the Reader 1. Power on the ACR-CRP12 by connecting it to a 12V power adapter. It will beep once, and the indicator light stays red. 2. Connect the device to your computer through USB. 3. Run the ACR-CRP12 tool to enter the **Connect Device** interface. 4. Select **USB** as the connect type. 5. Enter the Account Name and Password, both **admin** by default. 6. Click **Connect**. When your computer detects and connects to ACR-CRP12, “Connect Successful” will display. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-1729826952572.png) ### Part 1-2: Configure the Wiegand Format 1. Click **Wiegand Settings** and select the desired **Wiegand Format** from WG26, WG34, and WG58. > [!NOTE] > Note > > Please note that the Wiegand Format(Wiegand Card Reader Mode) should be consistent between the ACR-CRP12 and door phones/access control terminals for data transmission. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-1729827236572.png) 1. Click **Save Changes**. ## Part 2: Configure the ACR-CID12 The ACR-CID12 inputs the read data into the selected card number field. - For detailed features, refer to the [ACR-CID12 Tool Administrator Guide](/v1/docs/akuvox-acr-cid12-tool-administrator-guide). - Download the configuration tool from the [ACR-CID12 Tool page](/v1/docs/acr-cid12-tool). ### Part 2-1: Connect to the ACR-CID12 1. Connect the ACR-CID12 to your computer through USB. It will beep once, and the blue light stays on. 2. Run the ACR-CID12 tool and click **Connect**. When your computer detects and connects to ACR-CID12, “Connect Successful” will display in the lower left corner. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-3XYDY66C.png) ### Part 2-2: Configure the Output Format 1. Set **Output Format** to **Hex**. 2. Set **Start Bytes**, **Output Length**, and **Fill 00** based on the [Wiegand Format](/v1/docs/akuvox-vehicle-access-control-configuration#set-up-wiegand) selected in the ACR-CRP12. Please refer to the chart: | Door Phones | ACR-CRP12 | ACR-CID12 | | --- | --- | --- | | Wiegand Card Reader Mode | Wiegand Format | Start Bytes | Output Length | Output Format | Fill 00 | | Wiegand 26 | Wiegand 26 | 9 | 3 | Hex | ✔ | | Wiegand 34 | Wiegand 34 | 0 | 4 | Hex | X | | Wiegand 58 | Wiegand 58 | 0 | 7 | Hex | X | 3. Click **Save Changes**. ## Part 3: Configure the Door Phone or Access Control Terminal Configure the receiving device to use the same Wiegand format as the ACR-CRP12, and select the relay connected to the gate-opening circuit. ### Part 3-1: Configure Wiegand 1. Use the device’s IP to log into its web interface. The default username and password are both admin. 2. Go to the **Device > Wiegand** interface and select the Wiegand Card Reader Mode from Wiegand-26, Wiegand-34, and Wiegand-58. 3. Set the Wiegand Transfer Mode to **Input**. 4. Select the relay connected to the gate-opening circuit. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-S2RVDPVC.png) 1. Click Submit to save the settings. ## Part 4: Register UHF Tags and Configure Access Permissions ### Part 4-1: Local Deployment 1. Sign in to the device’s web interface. 2. Go to the **Directory > User** interface and click Add. 3. Set the User ID and Name. 4. In the **License Plate** section, move your mouse cursor to the code box and place the tag near the ACR-CID12. The device will beep and flash a green light once, and the code will be automatically displayed. > [!NOTE] > Note > > Disconnect the ACR-CID12 from its configuration tool before using it to read tag codes for registration. 1. Optionally, click **Duration** to set whether the vehicle is a long-term vehicle. If not, set the period when it can enter the parking lot. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-5AW2Q9QN.png) 1. Check the relay to be triggered and click Submit. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-OJ8MFONR.png) ### Part 4-2: SmartPlus Deployment For projects connected to SmartPlus Cloud, UHF tag credentials are managed through the cloud. The available configuration method depends on the project type and the user's role. Before proceeding, confirm that the device model and firmware meet the requirements for cloud-based credential management. #### Supported Models and Firmware | Model | Minimum Version | Model | Minimum Version | | --- | --- | --- | --- | | R29 | 29.30.10.404 | R28 V2 | 228.30.10.231 | | R25 | 25.30.10.117 | R20 | 320.30.11.30 | | E18 | 18.30.10.247 | E16 V2 | 216.30.10.208 | | X916 | 916.30.10.346 | X915 V2 | 2915.30.10.420 | | X912 | 912.30.11.107 | X912 V2 | 2912.30.12.110 | | A08 | 108.30.11.8 | X910 | 2910.30.11.28 | | A03 | 103.30.10.204 | A01/A02 | 101.30.10.206 | | A095 | 95.30.10.110 | A094 | 92.30.10.205 | | S535 | 535.30.11.8 | S539 | 539.30.10.403 | | A05V2 | 205.30.11.114 | S538 | 538.30.10.705 | | E12V2 | 312.30.11.106 | E16 V3 | 416.30.11.206 | | A15 | 1115.30.10.407 | S532 | 532.30.10.336 | | A13 | 1113.30.11.118 | WR01 | 1401.30.11.221 | #### Choose the Applicable Cloud Configuration Guide Different roles may have different permissions and entry points for managing credentials. Use the guide that matches your project and role. - **Commercial projects:** For new commercial projects created after October 15, 2024, installers, project managers, and administrators can add license plates. - For **installers and project managers**, refer to the Smart Access Project Management Guide — [License Plate Management](https://knowledge.akuvox.com/docs/akuvox-smartplus-property-manager-portal-guide-office#license-plate-management) chapter. - For **administrators**, refer to the Smart Access Web Portal Administrator Guide — [Personnel Management](https://knowledge.akuvox.com/docs/akuvox-smartplus-office-administrator-guide#personnel-management) chapter. - **Community projects:** Property managers can add UHF tags for community residents. Refer to the Smart Parking in Community Projects Guide — [Vehicle Management](https://knowledge.akuvox.com/docs/smart-parking#module-9-vehicle-management) chapter. - **Single-house projects:** Users can add UHF tags through the SmartPlus App. Refer to the [Open the Garage Door Guide](/v1/docs/open-the-garage-door). ## Part 5: Wiring and Verification The ACR-CRP12 requires a 12 V power supply and connects to the Akuvox door phone or access control terminal through Wiegand. Refer to the quick guides for the relevant devices for detailed wiring instructions. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-TV9I05LP.png) After completing the wiring and configuration: 1. Confirm that the ACR-CRP12 and the Akuvox device use the same Wiegand format. 2. Confirm that the relay selected in the device configuration is connected to the gate-opening circuit. 3. Present a registered UHF-TAG11 within the ACR-CRP12's detection range. 4. Verify that the device accepts the credential and triggers the configured relay. 5. If the gate does not open, check the tag registration, Wiegand format, relay selection, and wiring. ## Related - [[Video]Akuvox Vehicle Access Control Solution Setup](/videoakuvox-vehicle-access-control-solution-setup.md)