--- title: "Access Control Configuration" slug: "door-access-control-configuration-1" updated: 2025-06-03T02:03:18Z published: 2025-06-03T02:03:18Z canonical: "knowledge.akuvox.com/door-access-control-configuration-1" --- > ## Documentation Index > Fetch the complete documentation index at: https://knowledge.akuvox.com/llms.txt > Use this file to discover all available pages before exploring further. # Access Control Configuration ## Local Relay A local relay is the relay output built into the intercom device. It can directly control connected devices, such as door locks, by triggering actions based on user input or authorization. To set it up, go to the web **Device > Relay > Relay Setting** interface. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-XDU8NEDY.png) - **DTMF**: The DTMF code to trigger the local relay. - **Hold Delay**: Determine how long the relay stays activated. For example, if set to 5 seconds, the relay remains to be opened for 5 seconds before closing. - **Relay Type**: - **Chime Bell**: When there is a call and the relay is triggered, the chime bell will ring. - **Open Door**: When the unlock icon is pressed and the relay is triggered, the door will be opened. - **Other Switches(Reset By Event)**: The relay will reset after the triggered event is dealt with. ## Remote Relay The remote relay refers to the relay of another intercom, such as a door phone. During calls, users can enter a DTMF code or press the Unlock tab to unlock the door lock connected to the door phone. Set it up on the web **Device > Relay > Relay Setting > Remote Relay** interface. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-FHZZKC14.png) - **DTMF Code**: Define the DTMF code within the range(0-9 and *,#) for the remote relay. ## Web Relay A web relay has a built-in web server and can be controlled via the Internet or a local network. The device can use a web relay to either control a local relay, or a remote relay somewhere else on the network. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-1702022071712.png) Click [here](https://knowledge.akuvox.com/docs/configure-web-relay-on-door-phone-web-interface) to view how to set up web relay. To set it up, go to the web **Device > Relay > Web Relay Setting** interface. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-U89Y25IJ.png) - **IP Address**: The web relay IP address provided by the web relay manufacturer. - **Username**: The user name provided by the web relay manufacturer. - **Password**: The manufacturer-provided authentication key for the web relay. Authentication occurs via HTTP. Leaving the Password field blank indicates non-use of HTTP authentication. You can define the password using HTTP GET in the Web Relay Action field. - **Web Relay Action**: Configure the actions to be performed by the web relay upon triggering. Enter the manufacturer-provided URLs for various actions. > [!NOTE] > Note > > If the URL includes full HTTP content(e.g., http://admin:admin@192.168.1.2/state.xml?relayState=2), it doesn't rely on the IP address that you entered above. However, if the URL is simpler (e.g., "state.xml?relayState=2"), the relay uses the entered IP address. ## Door-opening Configuration ### Unlock by DTMF Code Dual-tone multi-frequency signaling(**DTMF**) is a way of sending signals over phone lines by using different voice-frequency bands. Users can use the DTMF function to unlock the door for visitors during a call by either typing the DTMF code on the soft keypad, or tapping the unlock tab with the DTMF code on the screen. To set it up, go to **Device > Relay > Relay Setting** interface. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-GS46AOF8.png) To configure the DTMF code transport format, navigate to the web **Account > Advanced > DTMF** interface. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-VDHO13O2.png) - **Type**: Select from the provided options. - **DTMF Code Transport Format**: There are four options, Disabled, DTMF, DTMF-Relay, and Telephone-Event. Configure it only when the third-party device that receives the DTMF code adopts the **Info** transport format. **Info** transfers the DTMF code via signaling while other transport format does it via RTP audio packet transmission. Select the DTMF transferring format according to the third-party device. - **DTMF Payload**: It is for data transmission identification ranging from 96-127. > [!NOTE] > Note > > To open the door with DTMF, the intercom devices that send and receive the unlock command must use the same mode and code. Otherwise, the DTMF unlock may fail. See [here](https://knowledge.akuvox.com/docs/how-to-open-the-door-via-dtmf-on-the-indoor-monitor) for the detailed DTMF configuration steps. ### Unlock via HTTP Command The device supports remote door unlocking via an HTTP command. Simply enable this feature and input the HTTP command (URL) for the device. This will trigger the relay and open the door, even if the users are away from the device. To set it up, go to the web **Device > Relay > Open Relay via HTTP** interface. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-LGS7R9LO.png) - **Username**: Set a username for authentication in HTTP command URLs. - **Password**: Set a username for authentication in HTTP command URLs. - **Remote Open Relay Via HTTP AllowList**: Enable it and type in the IP address of the server that you allow to send the HTTP command to the indoor monitor and trigger the local relay. > [!NOTE] > Note > > - If you do not set up the username and password, the remote door phone can trigger the indoor monitor’s relay without authentication. > - The URL format is http://{deviceIP}/fcgi/OpenDoor?action=OpenDoor&DoorNum=1. You can also set up HTTP commands to remotely control relays connected to door phones, go to the web **Device > Relay > Remote Relay By HTTP** interface. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-3G98J42G.png) - **IP/SIP**: Specify the IP or SIP number of the door phone. - **URL**: Enter the HTTP URL. - **Username**: Enter the username the same as that is configured on the door phone’s web interface. - **Password**: Enter the password the same as that is configured on the door phone’s web interface. - **DoorNum**: Specify the door to be opened. > [!WARNING] > Tip > > Here is an HTTP command URL example for relay triggering. > > ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-F9EUIST0(1).png) > [!NOTE] > **Note** > > The HTTP format for relay triggering varies depending on whether the device's high secure mode is enabled. Please refer to this how-to guide [Opening the Door via HTTP Command](https://knowledge.akuvox.com/docs/open-door-via-http-command) for more information. You can import and export the HTTP commands for quick setup on the **HTTP Command Import/Export** section. The imported file should be in XML format. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-1OJ1TBJV.png)