--- title: "IP-485 Multifunctional Gateway(ETAC-C1-R10) Configuration Guide" slug: "ip-485-multifunctional-gateway-etac-c1-r10-configuration-guide" updated: 2026-09-10T08:44:56Z published: 2026-09-10T08:44:56Z canonical: "knowledge.akuvox.com/ip-485-multifunctional-gateway-etac-c1-r10-configuration-guide" stale: true --- > ## Documentation Index > Fetch the complete documentation index at: https://knowledge.akuvox.com/llms.txt > Use this file to discover all available pages before exploring further. # IP-485 Multifunctional Gateway(ETAC-C1-R10) Configuration Guide ![Picture1](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-shohuf06.png) ETAC-C1-R10 # ## Before Getting Started 1. The multifunctional gateway can only be added to a family through a home center device. 2. Ensure that both the multifunctional gateway and the home center device are upgraded to the required firmware versions before configuration. The home center must be one of the supported models listed below. | **Supported Device** | **Required Firmware** | | --- | --- | | HyPanel (PS51) | 51.1.39.426 or later | | HyPanel V2 (PS51(V2)) | 251.1.39.406 or later | | HyPanel Plus (PS52) | 52.1.39.413 or later | | HyPanel KeyPlus (KS53) | 53.1.39.410 or later | | HyPanel Pro (PG71) | 71.1.39.423 or later | | HyPanel Ultra (PH81) | 281.1.39.415 or later | | HyPanel Supreme (PHX1) | 1001.1.39.412 or later | | HyPanel Elite 7 (PG42) | 42.1.38.93 or later | | SmartPanel (X933H) | 933.1.39.405 or later | | SmartPanel Elite 10 (C319H) | 119.1.39.405 or later | > [!NOTE] > **NOTE:** > > The configuration path may vary depending on the panel model and firmware version. Refer to the actual interface displayed on your device. 1. Ensure your computer, HyPanel device, and the multifunctional gateway are connected to the same local network. # ## Wiring > [!NOTE] > **NOTE:** > > Always turn off the circuit power before wiring! - The gateway can be powered by any of the following methods: - IEEE802.3af PoE - 12~24VDC - 100~240VAC, 50/60Hz - The gateway supports connections to: - RS485 devices - Relay outputs - Digital input terminals For detailed wiring and installation instructions, see [here](https://knowledge.akuvox.com/docs/ip-485-multifunctional-gateway-etac-c1-r10-quick-guide). # ## Operation Elements | **LED / Button** | **Status** | **Description** | | --- | --- | --- | | PWR/NET | Solid green | Power on; network normal | | Flashing red | Power on; network abnormal | | Flashing green | Pairing mode active | | LED 1-10 | Solid green/off | Relay active/inactive | | Off, no response when press the corresponding key | Relay fault | | KEY 1-10 | / | Press to turn relay on/off | | RESET | / | Press once to reboot the gateway | | / | Hold for more than 10 seconds to restore factor settings | # ## Add the Gateway to akubela System You can add the multifunctional gateway to the akubela system through an akubela home center device or the home center’s device web portal. ## ### Via akubela Panel 1. Ensure the PWR/NET LED is flashing green, indicating the gateway is in pairing mode. If not, check the network and power connections. 2. Choose the method based on your panel type: - **Large-Screen Panels** 1. On the Home screen, tap **Locations** at the top. 2. Select the room where you want to add the gateway. 3. Tap **+**, and wait for the gateway to be detected. 4. Select the detected gateway (identified by the last six digits of its MAC address). ![_data_code_DOWNLOAD_screen - 2025-10-24T155849.831](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-qloixuk8.png) 1. Name the gateway and assign its location, then tap **Done**. ![_data_code_DOWNLOAD_screen - 2025-10-24T155943.784](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-jl63efyv.png) - **Small-Screen Panels** 1. Swipe down from the top edge of any screen. 2. Tap ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-OTBGU1LO.png) **> Device Management >** ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-85U3K88Q.png). 3. Select the detected gateway and tap **Next**. ![_data_code_DOWNLOAD_screen - 2025-10-30T103432.431](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-vkoldxpf.png) 1. Name the gateway and assign its location, then tap **Done**. ## ### Via Device Web Portal 1. Enter the home center’s IP address in a browser to open its device web portal. > [!WARNING] > **TIP:** > > See [here](https://knowledge.akuvox.com/docs/log-into-device-web-portal) for detailed instructions. 1. Go to **Devices >** ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-QW307500.png) **> Add Device > Gateway Scan to add**, and select the home center device. 2. Wait for the gateway to be detected. 3. Click the detected gateway, then name it and assign its location. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-dekzq8tf.png) Once added, the gateway will appear in the akubela system, and its PWR/NET LED will turn solid green. # ## Access the Gateway Web Portal You can go to the gateway’s web portal to view basic and network information, manage connected devices, and perform operations such as factory reset, reboot, or firmware upgrade. ## ### From the Home Center Device Web Portal 1. Enter the home center’s IP address in a browser to open its device web portal. > [!WARNING] > **TIP:** > > The default login credentials are *admin/admin*. 1. Click the **Setting** button at the bottom of the gateway card. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-q6klutf3.png) 1. The gateway’s web portal will open in a new tab. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-xulrbs3w.png) ### Directly via Gateway’s IP Address 1. Obtain the gateway’s IP address. - If the gateway has been added to a family: On the home center device, go to **More > *[R10 gateway card]* >** ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-WLJNNYSY.png) **> IP address.** ![_data_code_DOWNLOAD_screen - 2025-10-24T173249.702](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-qaxkm423.png) - If not added: Check its IP address on the router’s management page. 1. Enter the gateway’s IP address in a browser. 1. Log in using one of the following: - If the gateway has been added to a family: Use the same credentials as the home center. - If not added: The default username and password are *admin/admin*. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-1787564491825.png) ## Configure Devices > [!NOTE] > **NOTE:** > > - Any relays, inputs, or RS485 devices configured before the gateway is added to a family will be retained automatically, so you don’t need to reconfigure them. > - Removing the gateway from the family will restore all its configurations to factory settings. ### Configure Relays 1. Log in to the gateway’s device web portal. 2. Go to **Device** **>** **Relays**. 3. Enable the desired relay and configure its settings. > [!NOTE] > **NOTE:** > > The configuration options vary by relay type. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-u534ob6d.png) | **Setting** | **Description** | | --- | --- | | Relay Name | Assign a name to identify the relay. | | Relay Type | Select the type. | | Power Off Memory | Choose whether the relay retains its state after a power outage. | | NCNO | Select the contact type based on wiring: - NO (Normally Open) - NC (Normally Closed) | | Combination *(Available when the relay type is* ***Shade-open, Shade-close, Heating,*** *or* ***Cooling****)* | - For **Shades**: Must link one shade-open and one shade-close relay to enable full shade control. - For **Heating/Cooling**: Optionally link a heating relay and a cooling relay, depending on the HVAC type. | | Upper Hysteresis Value *(Available when the relay type is* ***Heating*** *or* ***Cooling****)* | Set the upper temperature difference for hysteresis control. | | Lower Hysteresis Value *(Available when the relay type is* ***Heating*** *or* ***Cooling****)* | Set the lower temperature difference for hysteresis control. | | Temperature Source *(Available when the relay type is* ***Heating*** *or* ***Cooling****)* | Select the temperature sensor to use for control. | 1. Click **Submit** to save the settings. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-fwb5kzb7.png) Once added, the relays will appear in the family system. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-a9ytyoc2.png) ### Configure Digital Inputs 1. Go to **Device > Digital Inputs**. 2. Enable the desired input and configure as follows: ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-qm2vavvp.png) | **Setting** | **Description** | **Remark** | | --- | --- | --- | | Input Name | Assign a name to identify the input. | | | Hide in Device Page | Choose whether to hide this input on the akubela system. | Enabled by default for Shade types. | | Input Type | Select the type. | | | NCNO | Select the contact type based on wiring: - NO (Normally Open) - NC (Normally Closed) | | | Input Mode *(Available when the input type is* ***Shade-open, Shade-close,*** *or* ***Switch****)* | Choose: - **Logic Level**: High/low voltage control. - **Pulse**: Trigger-based control. | | | Control Mode *(Available when the input mode is* ***Logic Level****)* | Choose: - **Voltage Control**: High/low voltage toggles on/off (High = On, Low = Off). - **State Toggle**: Each press reverses the device state. | | | Click Duration *(Available when the input mode is* ***Pulse****)* | Set the duration of a short click. | | | Long Click Duration *(Available when the input mode is* ***Pulse****)* | Set the duration of a long click. | | | Link Relay/Output | Link this input to trigger a specific relay or output (shade type excluded) on the same gateway. | | | Combination Input *(Available when the relay type is* ***Shade-open*** *or* ***Shade-close****)* | Link another shade input to form a complete open/close pair. | | 1. Click **Submit** to save the settings. Once added, inputs that are not set to hidden will appear in the family system. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-5o7zlide.png) ### Configure RS485 Devices 1. Log in to the gateway’s device web portal, and go to **Device >** **RS485**. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-dgs7ep16.png) 1. Toggle the specific **RS485 enable** button to **On**. 1. Configure the parameters (Optional. Typically do not need to be changed) : - Baud Rate: Set the data transmission speed. *Default: 9600.* - Parity: Choose the error checking method. *Default: None.* - Data Message: *Default: 8.* - Stop Bits: *Default: 1.* ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-kxqqxv1i.png) 1. Click **New** to add an RS485 device. > [!NOTE] > **NOTE:** > > Currently supports Midea thermostats only. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-t4gdhjy6.png) 1. Enter the device name and device address. > [!NOTE] > **NOTE:** > > The entered address must match the address set on the device. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-q9ky1m56.png) 1. Click **Confirm**, and the device will appear in the list. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-dvoepbaz.png) 1. Click **Configuration** to open the device settings. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-tfs6tfne.png) ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-yo15zyqz.png) > [!NOTE] > **NOTE:** > > When configuring a Midea thermostat, set the **Register Address** under **Set Temperature** to **3** and click **Confirm**. No other parameter changes are required. > > ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-hiqpfqcl.png) 1. Click **Submit** to save. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-3wszx3o9.png) Once added, the device will appear in the family system. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-1spexqhw.png) # ## Maintenance ### Restart the Gateway To restart the gateway, use either of the following methods: - Press the physical RESET button once to reboot the gateway. - On the gateway’s device web portal, go to **Settings > Reboot**. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-z1irazfm.png) ### Restore Factory Settings To reset the gateway to factory settings, use either of the following methods: - Press the physical RESET button for about 10 seconds. - On the gateway’s device web portal, go to Settings > Reset. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-gotze81c.png) ## ### Upgrade Firmware 1. Contact akubela technical support to obtain the latest firmware file. 2. Log in to the gateway’s device web portal. 3. Go to **Settings > Import**, then upload the firmware file. ![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/ed-r10-configuration-guide-image-u8k8h1tj.png)