---
title: "Set Wiegand Connection for Access Control Terminals"
slug: "set-wiegand-connection-for-access-control-terminals"
updated: 2024-05-16T03:37:58Z
published: 2024-05-16T03:37:58Z
canonical: "knowledge.akuvox.com/set-wiegand-connection-for-access-control-terminals"
---

> ## Documentation Index
> Fetch the complete documentation index at: https://knowledge.akuvox.com/llms.txt
> Use this file to discover all available pages before exploring further.

# Set Wiegand Connection between A094 and Access Control Terminals

Akuvox door controller A094 and access control terminals can be connected via Wiegand. Users can open doors connected to A094 by swiping cards or entering PIN codes on the terminals.

This article takes A01 as an example.

## Connection

A094 has four Wiegand ports (A, B, C, and D). Specify the Wiegand port connected to the access control terminal, for example, Wiegand B.

![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-M87MAW9P.png)

Connect A094 and A01 through Wiegand D0, D1 and GND.

![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-S44VIIEU.png)

> [!WARNING]
> Tip
> 
> If you want to learn about how to wire door locks and A094, please refer to [A094 Quick Guide](https://knowledge.akuvox.com/docs/akuvox-a094-quick-guide-v10) for the complete wiring diagram.

## Set up A094

To open doors successfully, you need to set up Wiegand and assign the access method to the user.

1. Log into the device’s web interface with the username and password. The default is **admin**.
2. Navigate to the **Device > Wiegand** interface. Scroll to the Wiegand number that is used for connection.
3. Select the Wiegand Display Mode and Wiegand Card Reader Mode from the available options.
4. Select the Wiegand Transfer Mode as **Input**.
5. Check the Relay to be triggered.

![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-G9N2AVU0(1).png)

1. Click Submit to save the settings.

### Set Access Method

1. Go to the **Directory > User** interface and click **+Add**.
2. On the user-adding interface, enter the user’s ID and name.

![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-LHNC92NM(1).png)

1. Scroll to the **RF Card** section. Enter the card code.

![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-G9LZ81GJ.png)

1. Scroll to **Access Setting** section. Specify the relay to be triggered and the schedule when the user can open the door.

![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/图片-5QTFRVJ7-1.png)

1. Click Submit to save the settings.

## Set A01

1. Log into the device’s web interface with the username and password. The default is **admin**.
2. Navigate to the **Device > Wiegand** interface.
3. Select the Wiegand Display Mode and Wiegand Card Reader Mode the same as the [settings](/v1/docs/set-wiegand-connection-for-access-control-terminals#set-up-a094) in A094.
4. Set the Wiegand Transfer Mode as **Output**.

![](https://cdn.document360.io/f09a6106-e976-455e-b2d0-3d88b5385960/Images/Documentation/image-WNSXJXSY.png)

1. Click Submit to save the settings.

When the user swipes the card on A01, the relay connected to A094 will be triggered.