Manage Devices

Add ZigBee Devices

HyPanel Lux can connect to many ZigBee devices, such as sensors, emergency button, IR controller, thermostat, smart switch, and more. For example, you can add and fit a CO sensor in your kitchen to identify carbon monoxide leaks.

NOTE:
The transmission distances of ZigBee signal may vary by environmental characteristics and more. For optimal performance, add ZigBee devices to the HyPanel Lux within the same room.

Put devices in paring mode

Before pairing the ZigBee devices with the HyPanel, you should know how to activate their pairing mode. Here are a few examples to guide you.

TIP:
For more additional devices, check our guide on Put ZigBee Devices into Paring Mode, or refer to their manuals.

ZigBee device	How to put it to the pairing mode
Smart Emergency Button	Insert a pin into the reset hole at its back cover for 5 - 10s until the green light flashes quickly.
Smart Flood Sensor	Press and hold the reset button on the front for 5 - 10s until the green light flashes quickly.
Smart Temperature and Humidity sensor	Press and hold the reset button on the side for 5 - 10s until the signal icon flashes quickly.
Smart Motion Sensor	1. Rotate the battery cover anticlockwise to open. 2. Press and hold the reset button for at least 5s until the green light flashes quickly.
Smart Gas Sensor	Press and hold the reset button on the front for at least 5s until the green light flashes quickly.
Smart Smoke Sensor	Press and hold the reset button on the front for at least 5s until the green light flashes quickly.
Smart CO Sensor	1. Power on the sensor, and wait for its indicator light to change from yellow to green. 2. Press and hold the button on the front for at least 5s until the green light flashes quickly.
IR Controller	1. Power the controller by connecting it to a wall charger using the included USB cable. 2. Press and hold the button on the side of the controller until the green light flashes slowly and a beep sound is heard.

Pair devices with HyPanel Lux

Swipe down from the top edge of any screen, and tap > Device Management > . HyPanel Lux will then search for the nearby ZigBee devices.

Put the ZigBee device you want to add in paring mode.
The screen displays the searched device. Tap it to go to the next step.

NOTE:
If the device appears as Unknown, you can set its type before proceeding to the next step.

Name the device and choose its location, tap Done > Next.

The newly added device will be shown on both Device Management screen and the corresponding category screen.

You can also learn more about how to add ZigBee devices from user web portal or BelaHome app.

Add third-party smart home devices

Third-party smart home devices, such as Philips Hue, Ring Video Doorbell, Ecobee thermostat, Lutron Caseta, TP-Link kasa, Sonos, and more, can be added or removed on user web portal, or via BelaHome App.

To add a device, refer to any of the instructions:

Using BelaHome app;
On the user web portal.

See trigger histories of sensors

To see trigger histories of sensors, go to the corresponding catalog screen, select the desired sensor, and tap the logs.

To delete records, simply tap the icon in the upper right corner, select the logs, and tap .

Modify and delete devices

To view the details, relocate, or delete a device, do any of the following. Note that you can delete sensors and third-party devices like lights directly on the panel. For door phones and other panels, use the app or user web portal:

Go to > Device Management, and select the desired device.

Go to the Functions screen, select a desired category, and tap .

Using BelaHome app.
Go to the user web portal.

Control devices

Relays

The F51-R2-EU version of HyPanel Lux allows direct connection to two relays whose type can be switch, light, fan, heating/cooling system, and shade. You need to change the default relay type to the one you need via BelaHome app. For the detailed instructions, see here.

To open a relay, go to its corresponding type screen. Tap its button, and its background turns to be highlighted, indicating that the relay is opened.

To close the relay, tap it again, and its background dims.

Switch, plug, and socket

To turn on your switch, socket, siren or a light, on their specific function screen, find the desired device, and tap the button in the middle of the screen. Its background becomes highlighted, indicating that it is opened.

Lighting

Some lights can only be turned on or off with a single tap, while others like RGB lights, offer more features such as color adjustment, brightness control, and so on.

To control a RGB light, do the following:

Go to the Light screen.
Swipe through the screen to find the desired device, or tap to select from the list.
To turn the light on or off, tap .
To change the color temperature, tap , and rotate the knob to adjust the slider.

To change the light color, tap , and rotate the knob to pick the desired color from the palette.

To adjust its brightness, tap , then rotate the knob to adjust the brightness.

Heating, cooling, and thermostat

Heating and cooling

Go to the Climate screen, swipe through the screen to find the desired device, or tap to select from the list. Then do any of the following:

To close/open the device, tap the icon .

To adjust the target temperature, tap , and rotate the knob to adjust the temperature.

Thermostat

Go to the Climate screen, swipe through the screen to find the desired device, or tap to select from the list. Then do any of the following:

Tap to turn the thermostat on or off.
Rotate the knob to set up the desired temperature.
Tap to switch modes.
Tap to set fan speed.

Shade

Go to Climate , and find the desired shade relay.
Do any of the following:

Tap to open the shade.
Tap to close the shade.
Tap to stop the shade when it reaches the desired position.
Tap for advanced functions.

Calibration refers to adjusting the time it takes for the curtain to fully open and close. To do so, select this option and follow onscreen instructions.
Shade Reverse refers to reversing the curtain’s movement direction when the close and open buttons operate contrary to the current direction.

Speaker

When speakers such as SONOS are added, a Media category will be visible on the Functions screen for quick control of the speakers.

IR-based devices

Utilizing the IR controller, the panel can seamlessly integrate with up to 30 IR-based devices such as TVs and air conditioners, enabling it to function as a remote control. You can access the controller and its associated devices on the More screen.

NOTE:
The IR-based devices should be added via BelaHome app or specific HyPanel devices such as HyPanel Pro before you can see them on panels. For detailed instructions, see here.

To control the devices and remotes added by the specific IR controller, follow these steps:

For TVs and ACs

To simply turn them on/off, tap their respective icons on the More screen.

For additional functions, navigate to their corresponding feature screens:
a. TV: Found on the Media screen.

b. AC: Found on the Climate screen.

For customized remotes

Access them on the More screen by swiping left, where the buttons you added for the remote will appear.

Smart lock

Open door with one tap

Go to the Security screen, and tap .

Receive doorbell notification

When someone rings the doorbell on the smart lock, HyPanel Lux will display a push notification and play a sound to notify you.

Unlock with temporary key

You can provide visitors with a temporary PIN for self-door unlocking. To issue such keys, refer to the instructions with BelaHome app.

Upgrade lock’s software

To upgrade the lock’s software, select the desired smart lock, and tap > Update. This update option only shows up when there is a new version.

Use the intercom

Unlock door remotely

When you know who is at your door, you can open the door directly without communicating with the door phone.

Go to Security , and find the door phone.
Tap to open the door. Select the desired door to be opened if the door phone controls multiple doors.

If there are multiple doors connected to the door phone, select the desired one from the list.

Tap Confirm.

Unlock the door before answering a call

When you receive a call from the door phone with a camera, you can preview its monitoring streaming and open the door without answering the call.

Unlock the door during a call

You can answer the door phone call and unlock the door during the call.

On the calling screen, tap to release the door..

You are also able to call the door phone to see and hear who the visitor is. To do so, see the section Make voice calls in this guide.

See monitoring stream

If the connected door phone has a camera, you can see its monitoring stream on the HyPanel Lux.

To see the monitor stream, find the desired door phone, and tap on the monitor icon .