Add devices
HyPanel Elite 7 allows you to connect Zigbee devices and IR-based home appliances.
Zigbee devices
HyPanel Elite 7 can connect to many Zigbee devices, such as sensors, emergency button, IR controller, thermostat, smart switch, and more.
NOTE:
The transmission distances of Zigbee signal may vary by environmental characteristics and more. For optimal performance, add Zigbee devices to the HyPanel Elite 7 within the same room.
Put devices in pairing mode
Before pairing Zigbee devices with the HyPanel Elite 7, you should know how to activate their pairing mode. Here are a few examples to guide you.
TIP:
For more help pairing additional devices, check our guide on Put Zigbee Devices into Paring Mode, or refer to their manuals.
Zigbee device | How to put it to the pairing mode | |
Smart Emergency Button | Insert a pin into the reset hole at its back cover for 5 - 10s until the green light flashes quickly. |
|
Smart Flood Sensor | Press and hold the reset button on the front for 5 - 10s until the green light flashes quickly. |
|
Smart Temperature and Humidity sensor
| Press and hold the reset button on the side for 5 - 10s until the signal icon flashes quickly. |
|
Smart Motion Sensor
|
|
|
Smart Gas Sensor
| Press and hold the reset button on the front for at least 5s until the green light flashes quickly. |
|
Smart Smoke Sensor
| Press and hold the reset button on the front for at least 5s until the green light flashes quickly. |
|
|
|
|
IR Controller
|
|
|
Pair devices with HyPanel Elite 7
Tap
at the top of the Home screen.

Select the room where you want to add the device.

Tap the add icon
in the upper right corner. HyPanel Elite 7 will then search for the nearby devices.Put the Zigbee device you want to add in pairing mode.
The screen displays the searched device. Select it.
NOTE:
If the device appears as Unknown, you can set its type before proceeding to the next step.

Name the device and choose its location, tap Done.

The newly added device displays on the corresponding category screen.

IR-based devices
Using the infrared remote, HyPanel Elite 7 can integrate IR-based devices, and function as a remote controller.
NOTE:
When the HyPanel Elite 7 is used as a home center without cloud connectivity, it cannot control IR devices.
Add IR controller
You can use the IR controller to learn other remote controls or add TVs and air conditioners, supporting up to 30 devices.
Put the IR controller in pairing mode.
TIP:
You can see Pair devices with HyPanel Elite 7 for detailed instructions.
Tap
in the upper right and select a room to add the controller to.Tap
in the upper right corner.Wait for the IR controller to be detected, then tap it.

Change its name or location if needed.
The added controller is displayed on the More screen.

Add TV and AC
When HyPanel Elite 7 functions as the home center, it can directly control IR-enabled TVs and air conditioners.
These devices must be added via the BelaHome app. You can either add them to the IR Controller or add them directly to the panel. For detailed instructions, see here.
Door phones
HyPanel Elite 7 supports an auto-discovery function for door phones, which is enabled by default. After a reboot, initialization, or network change, the panel will automatically scan for door phones on the same LAN. Simply tap a detected device and confirm to add it.

Disable auto-discovery
To turn off this feature, go to Settings > System Settings > Installer Settings, and toggle off Auto-Discovery Doorphone.

See device logs
To see trigger histories of sensors, tap the desired device, and the logs display on the right.
To delete logs, tap the Clear icon
, and check specific logs. Or tap
to choose all and tap
.

Filter devices
The panel allows you to filter and display only the devices that are currently turned on. This works for Lights, Shades, Climate, and Electric Screens.
To enable this feature, tap the filter button in the upper right corner .

When the filter is active, only devices that are turned on will be displayed. To view all devices again, simply tap
to turn off the filter.

Relocate devices
To move the device from its current installation location to another, do the following.
NOTE:
The device must be online.
Tap the desired category tab on the Home screen.
Tap the desired device card to enter its control screen.
Tap
in the upper right corner.Tap Location, then select the new room for the device.
Tap Done.

Modify and delete devices
To view the details, relocate, or delete a device, do as the following:
Tap the desired category tab on the Home screen.
Tap the desired device card to enter its control screen.
Tap
in the upper right corner.

Tap Delete.

NOTE:
Deleting any relay on a device will result in the entire device being removed.















