Connect to the Internet
Typically, the network is configured by your service provider during installation. You can modify the Wi-Fi network or connect the device to a local area network (LAN) anytime, be aware that it may affect certain functions. To ensure continued proper operation, please check with your service provider before making any network changes.
NOTE：
All panels within the family should be in the same local network to ensure the proper communication. If you need to use SIP call and BelaHome app’s remote control function, panels must be connected to the cloud and Internet.
Change your Wi-Fi network
Swipe down from the top edge of any screen to open Control Center, and tap
> Wi-Fi.Choose the network you want to join.
Enter the password if required, and tap
> Connect.
TIP:
You can tap
in the upper right corner to view the HyPanel Plus’s IP address or toggle off DHCP to configure a static IP if needed.
Configure LAN network
To configure a LAN network:
Swipe down from the top edge of any screen, and tap
> Ethernet.On the Network view, do any of the following:
Toggle on DHCP feature, and the device will be assigned IP address automatically.
Toggle off DHCP feature, and enter IP Address, Sub-net Mask, Gateway, Preferred DNS Server, and Alternate DNS Server manually.
Configure network priority
You can set the preferred network when both Wi-Fi and Ethernet are connected.
To set up the priority, go to 
> Installer Settings > Network Priority Setting to choose which network the device should prioritize for communication.
Put HyPanel Plus in standby mode
To put HyPanel Plus in standby mode quickly, swipe down from the top edge of any screen to open Control Center, then tap 
.
You can customize how long the device takes to enter the standby mode by tapping 
> Display > Go into Standby. For example, if you choose 1 min, then HyPanel Plus will enter standby mode in 1 minute of inactivity.
Change screen saver settings
In Display Settings, you can turn the screen saver on or off, and choose the screen saver style.
Swipe down from the top edge of any screen, then tap
> Display.
Do any of the following:
Turn on or off the the toggle next to Screen Saver On.
When it is enabled, HyPanel Plus in standby mode will display photos and images; when disabled, the display just stays off.
Choose a screen saver style.
Select Photo Wall from the pull-down menu if you want to play images.
To add your preferred photos, see here.
Schedule the screensaver to turn on automatically by selecting Screen Saver Times.
NOTE:
When the panel is used in a GRMS project, any screensaver wallpapers sent from the GRMS system will override the default wallpapers on the panel. In addition, auto-brightness will be disabled automatically once the new wallpapers are applied.
Set up Do Not Disturb
To avoid interruptions from calls, messages, or notifications, enable Do Not Disturb(DND).
All calls and notifications will be silenced during the set period, while the alarm still rings.
Quickly Turn DND on or off
You can quickly turn the DND feature on by swiping down from the top edge of any screen, and tapping .png){kind=small}
. The icon will turn to 
when the DND is enabled. Tap the icon again to turn the DND off.
This feature can also be set up by going to 
> DND.
Schedule the DND to turn on automatically
To schedule a DND to turn on automatically at certain times, do as the following:
Swipe down from the top edge of any screen to open Control Center, and tap
> DND.Toggle on DND.
Toggle on Specific Time.
Set the DND start time and end time. DND will be activated automatically during the designated period and deactivated outside these hours.
Specifies the number of times the DND schedule will be repeated. The default setting is 1 time.
Protect your HyPanel Plus
For better security, use screen lock or settings lock to prevent unintended access to your device or the settings screen.
Set up system lock
Swipe down from the top edge of any screen to open Control Center, and tap
> System Lock.Do any of the following:
Toggle on Screen Lock to set a pattern password to unlock the screen when you wake it, and follow the onscreen instructions.
Toggle on Setting Lock to prevent unwanted access to the Settings screen, and follow the onscreen instructions.
NOTE:
The Screen Lock and Setting Lock use the same password. When both are active, you only need to input the password once to unlock both the device and the Settings screen.
To change the pattern password, on this System Lock screen, tap Set Screen Lock Password, draw the current pattern, and then set a new password.
Forgot password
To clear the forgotten current password, tap Forgot Password on the password required screen and follow the onscreen instructions. Two resetting options are provided based on your cloud connection status.
Via reset email
If you’ve registered the administrator account and ensure that the devices are connected to the Internet, a password reset email will be sent to the family’s administrator email address once you tap Forgot Password. Follow the instructions included to clear the password.
On the user web portal
Visit the user web portal, find the specific HyPanel Plus, and click
> Reset > Reset Panel screen lock password.
Configure proximity sensor settings
HyPanel Plus features a built-in proximity sensor that detects when someone approaches. For example, it can automatically wake the screen as you get near, offering a touch-free and responsive experience.
To adjust the sensor settings:
Swipe down from the top edge of any screen.
Tap
> Motion.Do any of the following:
Enable/Disable the proximity sensor.
Adjust the sensitivity to set the detection distance.
