Smart Parking in Community Projects for PMs

Prev Next

This guide walks you through configuring Smart Parking from start to finish. Each section tells you when you need it, whether it is required, and what you should see when it is done.

If you complete Parts 1–6 in sequence, your parking lot will be fully operational.

Part 1: Before You Start

Complete this section before opening Smart Parking. If any item is missing, later configuration will fail or behave unexpectedly.

Part 1-1: Service Activation

Item

Required

Who does it

Smart Parking service activated

Yes

Installer enables it during project setup, or PM enables it in Settings > Advanced Settings on the SmartPlus web portal.

Parking devices online and added to the project

Yes

Installer

Devices running a supported firmware version

Yes

Installer

How to verify you are ready: Open Smart Parking. If the module opens and shows the System Overview without an activation prompt, the service is active.

Note

The feature availability may vary by region. Contact Akuvox for local support details.


Part 1-2: Device Compatibility

Full Smart Parking features are supported ONLY on:

Model

Minimum Version

R29

29.30.10.740

S538

538.30.10.722

S539

539.30.10.711

Other supported models ONLY provide resident license plate and UHF tag recognition. See Part 7-4. They do not support the rules in Part 4, parking logs, or parking-space statistics.

Part 1-3: What to Confirm with Your Installer

Before you continue, ask the installer three questions:

  1. Which vehicle recognition method is used — LPR camera or ACR-CRP12 UHF reader? This determines which rules you can use at all. See Part 2.

  2. Which devices serve as the entry gate and exit gate? You will associate them in Part 3-3.

  3. Is the parking lot a single-gate or multi-gate layout? This decides the Door Mode in Part 3-1.

Write the answers down. You will need them in Parts 2, 3, and 4.


Part 2: Understand Your Parking Setup

Part 2-1: The Two Recognition Methods

Method

What identifies the vehicle

Hardware

Method 1 — LPR

The license plate

Third-party LPR camera

Method 2 — UHF

The UHF card on the windshield

Akuvox ACR-CRP12 long-range reader

Part 2-2: What You Can and Cannot Do with Each Method

Capability

Method 1(LPR)

Method 2(UHF)

Resident vehicle access

✔

✔

Temporary vehicle access

✔

✔

Visitor parking time & free quota

✔

X

Overtime charging

✔

X

U-turn restriction & violation counting

✔

X

Blocklist enforcement

✔

X

Emergency vehicle rules

✔

X

Auto access rules

✔

X

Parking logs

✔

X

Parking-space statistics

✔

X

Offline recognition

✔

X

Important

Method 1 (LPR) unlocks the full Smart Parking rule set. Method 2 (UHF / ACR-CRP12) provides vehicle identification and access only — it does NOT support visitor parking time, overtime charging, U-turn restrictions, etc., listed above.

This decision is usually made by the installer at project design time. Confirm it before configuring.

Part 2-3: One Behavior to Remember

If a vehicle has both a license plate and a UHF card configured, the cloud sends only the UHF code to the door phone. The device identifies the vehicle by UHF and ignores the license plate.

Consequence: In a Method 2 project, you must fill in both the plate and the UHF card, but only the UHF card is actually used for recognition. See Part 5-1.


Part 3: Set up Your Parking Lot

This section creates the parking lot itself. Parts 3.1 and 3.2 are required. Part 3.3 is optional — it only records gate information and does not control any hardware. Part 3.4 tells you how to verify the setup before moving on to rules.

Part 3-1: Create a Parking Lot

When: Once per parking lot. Required: Yes.

  1. Log in to the SmartPlus Cloud platform with your PM account.

  2. Click Smart Parking > Parking Lot in the left menu.

  3. Click New on the right to create a new parking lot.

  1. Name the parking lot.

  2. [Optional]Upload the Parking Lot Logo. Requirements are a square image, ≥200x200px, supported formats: JPG/JPEG/PNG/BMP.

  3. Select the Door Mode:

  • Single Door — one gate handles both entry and exit. The system treats the first recognition as entry and the second as exit.

  • Multiple Doors — you define which gate is entry and which is exit.

  1. Click Submit.

When done, you will see: the new parking lot in the list, with a vehicle count of 0.

  • Click to delete it.

  • Click to view more details and modify the settings.

Part 3-2: Configure Parking Spaces

When: If the lot has a capacity limit. Required: Optional.

  1. Open the parking lot you just created.

  2. Set Parking Spaces (0~65535). 0 or empty = no limit.

  3. Set whether vehicles may enter when the lot is full. Default is No (entry blocked at capacity).

  1. Submit the settings.

When done, you will see: the capacity reflected in the parking lot list.

Caution

This setting does nothing in UHF projects. Capacity control depends on parking logs and space statistics, which UHF projects do not generate. In a Method 2 (UHF) project, the system cannot know how many vehicles are inside, so "deny entry when full" will not take effect.

Part 3-3: Configure Entry and Exit Gates (Optional)

When: Only if you want gate information recorded in the platform for reference. Required: No.

Gate Management currently only stores gate information for display and reference. The cloud cannot yet establish a functional link with cameras or display screens.

  1. Click Smart Parking > Parking Lot > Gate Management > New.

  1. Enter a unique Gate Number to distinguish the gate from others.

  2. Choose the parking lot.

  3. Enter the Gate Name, e.g., Exit Gate.

  4. Select the Entrance/Exit Name from the list.

  5. Associate the required equipment.

    If Camera and/or Display Screen is checked, specify the device number.

  1. Submit the settings.

When done, you will see: the gate listed under Gate Management with its entry/exit role. This entry is informational; it does not alter how the gate operates.

After creating a gate, click to modify the settings and to remove it.

Part 3-4: Verify the Setup

Before moving to Part 4, confirm:

  • The parking lot exists with the correct Door Mode (Single Door / Multiple Doors).

  • If Multiple Doors: entry and exit are correctly defined.

  • Parking space capacity is set, or intentionally left unlimited.

  • (Optional) Gate records created, if you want them for reference.

Tips

Drive or simulate one vehicle through the gate. If a record appears under Vehicle Log, the gate and devices are working together correctly.

If no log appears, stop here and contact your installer — rules in Part 4 operate on top of log capture and will not work without it.


Part 4: Configure Vehicle Rules

All four rules in this section are evaluated on the license plate. They do not apply to vehicles identified by UHF card. If your project uses Method 2, skip this section.

Part 4-1: Visitor Parking Time

When you need it: Visitor vehicles park for free up to a quota, then incur charges. Required: No — skip if visitors pay a flat rate or are not charged.

Typical use: residential communities that give each apartment a monthly free-visitor allowance.

Enable Visitor Free Parking Time

  1. Click Smart Parking > Setting.

  2. Enable the feature.

  3. Configure the Visitor Free Parking Time per Apartment(minutes per month)(0~65535 minutes) and Overtime Charging Rate(fee per minute).

  1. Submit the setting.

After the configuration, apartment visitor parking statistics become visible. Visitor overtime fees can be calculated automatically.

Apartment Visitor Parking Configuration

You can define visitor parking time per apartment.

  1. Click Apartments.

  2. Click of a specific apartment, or make a bulk configuration by checking apartments and clicking Batch Edit.

  3. Choose Follow Project Settings(Configured on the Smart Parking > Settings interface) or Custom.

    If Custom is selected, specify the Visitor Free Parking Time(0~65535 minutes) for the apartment.

  1. Submit the setting.

When done, you will see: visitor parking statistics per apartment under Smart Parking > Apartment Management, showing remaining vs. total quota. Overtime fees are calculated automatically.

You can click to view the parking time using details, and click to modify the parking time.

Note

Parking duration is counted after deducting the U-turn grace period. With a 30-minute grace period, a 50-minute visit consumes only 20 minutes of the apartment's quota. See Part 4-2.

Part 4-2: U-Turn Restrictions

When you need it: Vehicles that enter and immediately leave should not be counted as parking, and repeat offenders should be restricted. Required: No — skip if you do not need to exclude short drop-offs.

Typical use: preventing ride-hailing drop-offs and delivery vehicles from consuming resident visitor quota.

Understand the rule

If grace period = 30 minutes:

  • Vehicle exits within 30 minutes → treated as a U-turn

  • Vehicle exits after 30 minutes → counted as parking

  1. Click Smart Parking > Setting.

  2. Configure the Grace Period Duration(0~65535). Setting it to 0 means no restrictions.

  3. Configure the Blocklist Enforcement Threshold. This defines how many U-turn violations are allowed before restriction. For example, if it is set to 5, upon the 6th violation, the vehicle will be blocklisted.

  1. Submit the setting.

Part 4-3: Emergency Vehicle Access

When you need it: Fire, ambulance, or police vehicles must always be able to enter. Required: No — but strongly recommended for every community.

Typical use: safety compliance. Emergency vehicles bypass all other restrictions.

  1. Click Smart Parking > Setting.

  2. Click New in the Emergency Vehicle Access Rules section.

  3. Enter the Rule Name.

  4. Enter the Prefix and/or Suffix of the license plate.

  • Only Prefix → match prefix to enter

  • Only Suffix → match suffix to enter

  • Both → match both to enter

  1. Enter the rule description as needed.

  1. Submit the setting.

When done, you will see: the rule in the list, with a toggle to enable or disable it. Up to 20 rules are supported.

Note

Emergency vehicles bypass everything — blocklist, U-turn restrictions, and active Auto Access rules.

Part 4-4: Auto Access Rules

When you need it: All vehicles should pass freely during specific time windows — for example, open-house events or scheduled public access hours. Required: No — only for exceptional time windows.

Note

During an active window, all vehicles may enter and exit — including blocklisted vehicles. No individual check is performed. Enable it only for windows where unrestricted access is genuinely intended, and disable it afterwards.

  1. Click Smart Parking > Setting.

  2. Click New in the Auto Access Rule section.

  3. Enter the Configuration Name.

  4. Specify the auto access time.

  5. Enter the rule description as needed.

  1. Submit the setting.

When done, you will see: the rule in the list with a toggle. Up to 20 rules are supported.


Part 5: Manage Vehicles

You can add vehicles, view entry records, configure monthly parking fees, and add remarks.

Part 5-1: Add and Manage Resident Vehicles

When: For every resident vehicle. Required: Yes.

  1. Click Smart Parking > Vehicle > New.

  1. Select the building, apartment, and resident.

  2. Fill in the vehicle identification.  In a Method 2 project, you must fill both, but only the UHF card is actually used for recognition.

Field

Method 1(LPR)

Method 2(UHF)

License Plate

Required

Required

UHF Card

Leave Empty

Required

  1. Configure Long-term Vehicle. It is enabled by default. If disabled, set a period when the vehicle can enter and exit the parking lot.

  2. Set the Monthly Fee for the resident.

  3. Add remarks as needed.

  1. Submit the setting.

When done, you will see: the vehicle in the list.

You can click to view its entry/exit logs, click to modify the setting, and to remove the vehicle.

Part 5-2: Manage Blocklisted Vehicles

When: A vehicle must be denied entry. Required: No.

Behavior: Blocklisted vehicles can exit but cannot enter.

Add a vehicle to the blocklist

  1. To blocklist a vehicle manually, click Smart Parking > Vehicle > Blocklist > New.

  2. Enter the license plate.

  3. Enter the reason as needed.

  1. Submit the setting.

When done, you will see: the vehicle in the blocklist with status Blocklisted.

Remove from the blocklist

To unblock, click to remove it from the blocklist. Its Current Status will change to Removed, and the vehicle can enter the parking lot.

When a blocklisted vehicle may still enter

Situation

Allowed?

Blocklisted only for U-turn timeout, and current violation count is now ≤ threshold

Yes

An Auto Access Rule window is currently active

Yes

Matches an Emergency Vehicle Rule

Yes

Any other case

No

Part 5-3: Record Resident Violations

When: A resident breaks parking rules and needs a formal notice. Required: No.

  1. Click Smart Parking > Vehicle > Resident Violations > New.

  1. Select the building, apartment, resident, and license plate.

  2. Enter the reason as needed.

  1. Submit the setting.

When done, you will see: the record in the violation list, and the resident receives a notification in the SmartPlus App.


Part 6: Daily Parking Management

Part 6-1: View Vehicle Logs

When: Daily — to check activity, resolve disputes, or audit. Required: Ongoing.

  1. Click Smart Parking > Parking Lot.

  2. Click of the target parking lot.

  3. Click Vehicle Log, where you can:

  • Check the vehicle entry/exit time and parking duration.

  • Click Import to upload vehicles already in the parking lot.

  • Click Export to download logs.

The import template:

Part 6-2: Mark Vehicles Exited Manually

When: A vehicle left but no exit was captured — for example, an LPR recognition failure, or a vehicle that drove out without being detected. Required: As needed, but important — skipping it corrupts the vehicle count.

Caution

If you skip this step after a failed exit capture, the parking space count remains incorrect. This can cause the system to incorrectly block entry when it thinks the lot is full, even when spaces are actually available.

  1. Click Smart Parking > Parking Lot.

  2. Click of the target parking lot.

  1. Click in the Actions column to manually mark that the vehicle has left the parking lot.

Part 6-3: Monitor Parking Status

When: Daily. Required: Ongoing.

The System Overview page gives you a quick health check without opening multiple pages.

Use the shortcut buttons on this page to jump directly to adding vehicles or managing resources.


Part 7: Rule Priority and Reference

This section is reference material. You do not need it to configure the system, but it explains why certain outcomes occur.

Part 7-1: Rule Priority

When multiple rules are active at the same time, the system resolves conflicts using the following priority order. A higher-priority rule always overrides a lower one.

Priority

Rule

Behavior

1 (Highest)

Emergency Vehicle Rule

Grants entry regardless of any other restriction, including blocklist status.

2

Auto Access Rule

Grants entry to all vehicles during the configured time window, overriding standard vehicle checks.

3

Blocklist Restriction

Blocks entry for non-emergency vehicles that are blocklisted.

4

Long-term / Temporary Vehicle

Standard vehicle access based on configured schedule and permissions.

5 (Lowest)

Visitor Default

Visitor vehicles follow the parking duration and charging rules configured in Module 4.

Part 7-2: Special Cases

Situation

Outcome

Vehicle has both plate and UHF card

Cloud sends UHF only; device ignores the plate

Blocklisted only for U-turn, threshold later raised above violation count

Vehicle may enter

Auto Access window active

All vehicles may enter, including blocklisted

Emergency rule matches the plate

May enter regardless of everything else

UHF project, any plate-based rule

Not applicable

Part 7-3: Offline Operation

Item

Supported

Models

R29, S538, S539 only

Recognition method

License plate (LPR) only

Resident vehicles

Enter and exit normally

Emergency vehicles

Enter and exit normally

Visitor vehicles

Not supported

Log synchronization

Uploaded automatically after reconnection

Part 7-4: Device Compatibility

Full features:

Model

Minimum Version

R29

29.30.10.740

S538

538.30.10.722

S539

539.30.10.711

Resident plate and UHF recognition only:

Model

Version(or higher)

Model

Version(or higher)

R28 V2

228.30.10.231

R20

320.30.11.30

R25

25.30.10.117

X915 V2

2915.30.10.420

X916

916.30.10.346

X910

2910.30.11.28

X912

912.30.11.107

E16 V2

216.30.10.208

X912 V2

2912.30.12.110

E16 V3

416.30.11.206

E18

18.30.10.247

A01/A02

101.30.10.206

A08

108.30.11.8

A094

92.30.10.205

A03

103.30.10.204

S535

535.30.11.8

A095

95.30.10.110

E12V2

312.30.11.106

A05

205.30.11.114

A15

1115.30.10.407

S532

532.30.10.336

A13

1113.30.11.118

WR01

1401.30.11.221