Akuvox S535 Door Phone Administrator Guide
- 29 Articles
- Updated on Oct 8, 2026
- Published on Mar 2, 2026
Thank you for choosing the Akuvox S535 series door phone. This manual is intended for administrators who need to properly configure the door phone. This manual applies to version 535.30.11.46, and it provides all the configurations for the functi...
- Updated on Aug 5, 2025
The S535 touchscreen intercom is a cutting-edge device with a compact design featuring a robust metal exterior that provides excellent weather resistance and aesthetic appeal. The luxurious combination of gunmetal stainless steel and black glass ...
- Updated on Oct 8, 2026
- Published on Sep 3, 2025
What’s new in version 535.30.11.42: Support up to 50,000 users . Support Video/Radar screensaver wake-up mode . Support using barcodes as a card credential with face recognition for two-factor authentication . Optimized the integr...
- Updated on Sep 15, 2026
- Published on Jun 15, 2026
Supported Card Types The device firmware should be S535.30.10.233 or higher: Unencrypted ID Card: EM4100 EM4200 Unencrypted IC Card: Mifare Ultralight C/EV1 Mifare Classic Compatible Card Mifare Desfire EV1 2K D21 Mifa...
- Updated on Aug 5, 2025
Door phones' system settings can be accessed either on the device or on its interface. Access the Device Settings on the Device Before configuring the door phone, please make sure the device is installed correctly and connected to a normal netwo...
- Published on Nov 5, 2026
Status : This section gives you basic information such as product information, network information, call log, and door log. Account : This section concerns the SIP account, SIP server, proxy server, transport protocol type, audio & video ...
- Updated on Oct 8, 2026
- Published on Mar 6, 2026
Language Set up the language during initial device setup or later through the device or web interface according to your preference. On the Web Select the LCD language on the Setting > Time/Lang > LCD Language interface. The following l...
- Updated on Jun 15, 2026
- Published on Mar 2, 2026
Volume Configuration You can configure the volume of the microphone, speaker, etc. Moreover, you can also set up the tamper alarm volume when unwanted removal of the device occurs. On the Web Set up volumes on the web Device > Audio interf...
- Published on Apr 20, 2026
Infrared LED Setting Infrared LED is mainly designed to reinforce the light at night or in a dark environment. Set it up on the web Device > Light > LED interface. Mode : Auto : Turn on the infrared LED automatically based on ...
- Updated on Oct 8, 2026
- Published on Apr 3, 2026
You can set up the device's screen display features such as screensaver to give users a better visual and operational experience. Home Screen Display The device supports Villa , Building , Speed Dial , QR code, and Two Column Speed Dial t...
- Updated on Aug 5, 2025
Device Network Configuration To ensure normal functioning, make sure that the device has its IP address set correctly or obtained automatically from the DHCP server. Check the network status on the web Status > Info > Network Information ...
- Published on Jun 26, 2026
IP Call Configuration An IP call is a direct call between two intercom devices using their IP addresses, without a server or a PBX. IP calls work when the devices are on the same network. Make IP Calls Make IP calls by entering the IP number, s...
- Published on Jul 14, 2026
Quick Dial By Number Replacement The dial number replacement feature simplifies long and complex dial numbers of the device, providing shorter and more user-friendly alternatives for making calls. It allows the substitution of multiple dial number...
- Updated on Aug 5, 2025
Audio Codec The door phone supports three types of codecs (PCMU, PCMA, and G722) for encoding and decoding the audio data during the call session. Each type of codec varies in terms of sound quality. PCMU and PCMA are well-suited for traditional te...
- Updated on Aug 5, 2025
The local contact information is used to initiate SIP or IP calls to users. You can group the contact information to facilitate group calls to target users. Moreover, the contact list functions as a whitelist, allowing only listed numbers to open d...
- Updated on Jun 1, 2026
- Published on Jun 1, 2026
Local Relay A local relay is the relay output built into the intercom device. It can directly control connected devices, such as door locks, by triggering actions based on user input or authorization. You can configure the relay switch and DTMF ...
- Published on Jun 1, 2026
A door access schedule lets you decide who can open the door and when. It applies to both individuals and groups, ensuring that users within the schedule can only open the door using the authorized method during designated time periods. Create a ...
- Updated on Oct 8, 2026
- Published on Mar 2, 2026
Unlock by Public PIN There are two types of PIN codes for door access: public and private. A private PIN is unique to each user, while the public one is shared by residents in the same building or complex. You can create and modify both the public...
- Published on Nov 5, 2026
MJPEG and RTSP are the primary monitoring stream types discussed in this chapter. MJPEG, or Motion JPEG, is a video compression format that uses JPEG images for each video frame. Akuvox devices display live streams on the web interface and c...
- Updated on Jun 15, 2026
- Published on Mar 12, 2026
Tamper Alarm The tamper alarm function prevents anyone from removing the device without permission. Akuvox devices support two types of tamper proof: gravity detection and button status detection. Click here to view which type is supported by t...
- Updated on Aug 5, 2025
Call Logs To check calls—including dial-out, received, and missed calls—within a specific period, you can view the call log on the device's web interface. If needed, you can also export the call log from the device. Check call logs on the web S...
- Updated on Sep 11, 2026
- Published on May 7, 2026
Integration via Wiegand The Wiegand feature enables the Akuvox device to act as a controller or a card reader. Set it up on the web Device > Wiegand interface. Wiegand Display Mode : Select the Wiegand card code format from the follo...
- Updated on Apr 3, 2026
- Published on Mar 2, 2026
Akuvox Lift Control The device can be connected to the Akuvox lift controller for the lift control. Users can summon the lift to go down to the ground floor when they are granted access through various types of access methods on the device. Click...
- Updated on Aug 5, 2025
Akuvox devices can be upgraded on the device web interface. Upgrade the firmware on the web System > Upgrade interface. Note Firmware files should be in .rom format for upgrade.
- Updated on Jul 1, 2025
Provisioning Principle Auto-provisioning is a feature used to configure or upgrade devices in batch via third-party servers. DHCP, PNP, TFTP, FTP, and HTTPS are the protocols used by the Akuvox devices to access the URL of the address of th...
- Updated on Jul 1, 2025
System Log for Debugging System logs can be used for debugging purposes. Set it up on the web System > Maintenance > System Log interface. Log Level : Select log levels from 1 to 7 levels. You will be instructed by Akuvox technica...
- Published on Jun 17, 2026
You can import or export encrypted configuration files to your Local PC. Set it up on the web System > Maintenance > Others interface. The import file should be in .tgz/.conf/.cfg format. Config File : Click Export to export con...
- Updated on Aug 5, 2025
Accounts Management You can add administrator and user accounts and configure their passwords for logging into the device web interface. Navigate to the web System > Security > Account Management interface. Click +Add to create an accoun...
- Updated on Aug 5, 2025
Reboot Reboot the device on the web System > Upgrade interface, or on the Setting > Advanced Setting screen. You can set up the reboot schedule on the web System > Auto Provisioning > Reboot Schedule interface. Reset T...