Akuvox X915 Series Door Phone Administrator Guide
- 30 Articles
- Updated on Oct 28, 2026
- Published on Mar 4, 2026
Thank you for choosing the Akuvox X915 series door phone. This manual is intended for administrators who need to properly configure the door phone. This manual applies to version 2915.30.10.826, and it provides all the configurations for the func...
- Updated on Nov 13, 2024
The Akuvox X915 series is an Android-based IP video door phone with a touch screen. It combines audio and video communication, access control, and video surveillance functionalities. With its advanced Android OS, Cloud, and AI-based communication te...
- Updated on Oct 28, 2026
- Published on Jan 25, 2025
What’s new in version 2915.30.10.826: Support for 6HN Wiegand Display Mode . Support for the Use First 3 Bytes option for IC Card Display Mode and Wiegand Display Mode settings to use the first three bytes of the card number without ad...
- Published on Jun 15, 2026
Supported Card Types The device’s firmware should be 2915.30.10.416 or higher: Unencrypted ID Card: EM4100 EM4200 HID-Prox HID-iClass Only X915 V2.0 with an HID-LF or HID-HF module supports reading the HID iClass or HID Prox car...
- Updated on Mar 20, 2025
Door phones' system settings can be accessed either on the device or on its interface. Access the Device Settings Before configuring the device, please ensure the device is installed correctly and connected to a normal network. You can set up s...
- Published on Nov 25, 2025
Since version 2915.30.10.611, X915V2 supports searching for features on its web portal. For example, if you want to search for motion detection, enter the value in the upper search box. Then, select the desired option to redirect to the configurat...
- Published on Nov 5, 2026
Quick Start : This section provides quick access to the device’s key settings, such as network, user, relay, etc. Device Management : Status: This section gives you basic information, such as product information, network information, acc...
- Published on Mar 4, 2026
Language Set up the language during initial device setup or later through the device or web interface according to your preference. On the Web Select the LCD language on the Setting > Time/Lang > LCD Language interface. The device...
- Published on Oct 28, 2026
Volume Configuration You can configure the volume of the microphone, speaker, etc. Moreover, you can also set up the tamper alarm volume when unwanted removal of the device occurs. On the Web Set up volumes on the web Device > Audio interf...
- Published on Oct 21, 2026
Infrared LED Setting Infrared LED is mainly designed to reinforce the light at night or in a dark environment. On the Web Set it up on the web Device > Light > LED interface. Mode : Auto : Turn on the infrared LED automa...
- Updated on Oct 28, 2026
- Published on Jul 22, 2026
Home Screen Display The device supports Villa, Building, Office, and Alphanumeric themes. You can apply the desired theme to different scenarios. Select the theme on the Setting > Key/Display > Theme interface. Villa Theme You can...
- Updated on Jun 13, 2025
Device Network Connection To ensure normal functioning, make sure that the device has its IP address set correctly or obtained automatically from the DHCP server. Check the network status on the web Status > Info > Network Information in...
- Updated on Oct 21, 2026
- Published on Sep 10, 2026
IP Call Configuration An IP call is a direct call between two intercom devices using their IP addresses, without a server or a PBX. IP calls work when the devices are on the same network. IP Call Setup Enable the IP direct call on the Intercom...
- Updated on Aug 18, 2025
Quick Dial By Number Replacement The dial number replacement feature simplifies long and complex dial numbers of the device, providing shorter and more user-friendly alternatives for making calls. It allows the substitution of multiple dial number...
- Updated on Mar 20, 2025
Audio Codec The door phone supports three types of codec (PCMU, PCMA, and G722) for encoding and decoding the audio data during the call session. Each type of codec varies in terms of sound quality. PCMU and PCMA are well-suited for traditional tel...
- Updated on Jun 3, 2025
The local contact information is used to initiate SIP or IP calls to users. You can group the contact information to facilitate group calls to target users. Moreover, the contact list functions as a whitelist, allowing only listed numbers to open d...
- Updated on Jan 16, 2026
Local Relay A local relay is the relay output built into the intercom device. It can directly control connected devices, such as door locks, by triggering actions based on user input or authorization. Set it up on the Access Control > Relay ...
- Updated on Jan 16, 2026
A door access schedule lets you decide who can open the door and when. It applies to both individuals and groups, ensuring that users within the schedule can only open the door using the authorized method during designated time periods. Create a ...
- Updated on Nov 16, 2026
- Published on Mar 4, 2026
Unlock By Public PIN There are two types of PIN codes for door access: public and private. A private PIN is unique to each user, while the public one is shared by residents in the same building or complex. You can create and modify both the public...
- Published on Nov 5, 2026
MJPEG and RTSP are the primary monitoring stream types discussed in this chapter. MJPEG, or Motion JPEG, is a video compression format that uses JPEG images for each video frame. Akuvox devices display live streams on the web interface and c...
- Published on Jul 13, 2026
Tamper Alarm The tamper alarm function prevents anyone from removing the device without permission. Akuvox devices support two types of tamper proof: gravity detection and button status detection. Click here to view which type is supported by t...
- Updated on May 14, 2026
- Published on Mar 4, 2026
Call Logs To check calls—including dial-out, received, and missed calls—within a specific period, you can view the call log on the device's web interface. If needed, you can also export the call log from the device. Check the call log on the web...
- Updated on Oct 28, 2026
- Published on Apr 14, 2026
Integration via Wiegand The Wiegand feature enables the Akuvox device to act as a controller or a card reader. Set it up on the web Device > Wiegand interface. Wiegand Display Mode : Select the Wiegand card code format from the ...
- Updated on Jan 26, 2026
Akuvox Lift Control The device can be connected to the Akuvox lift controller for the lift control. Users can summon the lift to go down to the ground floor when they are granted access through various types of access methods on the device. Click...
- Published on Aug 28, 2026
Upgrade the firmware on the System > Upgrade interface. If you want to reset the device after the upgrade, check the Reset box. Note Firmware files should be in .zip format for the upgrade. Click here to download th...
- Updated on Oct 16, 2026
- Published on Oct 16, 2026
You can configure and upgrade the device through the web interface using one-time or scheduled auto-provisioning with configuration files. This eliminates the need to set up configurations manually, saving you time and effort. Provisioning Princi...
- Published on Oct 9, 2026
System Log for Debugging System logs can be used for debugging purposes. Set it up on the web System > Maintenance > System Log interface. Log Level : Select log levels from 1 to 7 levels. You will be instructed by Akuvox technica...
- Published on Jun 17, 2026
You can import or export encrypted configuration files to your Local PC. Set it up on the web System > Maintenance > Others interface. Config File : Scope: Config import/export includes configuration settings, user data (inc...
- Updated on Feb 12, 2026
Modify Device Web Interface Password Change the web password on the web System > Security > Web Password Modify interface. Select Admin for the administrator account and User for the user account. Click the Change Password ...
- Updated on Mar 25, 2025
Reboot Reboot the device on the System > Upgrade interface. You can set up the reboot schedule on the System > Auto Provisioning > Reboot Schedule interface. You can also reboot the device on the Setting > Advanced Setting ...